Back to Blog

Hardware

Framing Nails Guide: Types, Sizes, Angles and How to Choose

timberCentral 10 Min Read
Framing Nails Guide: Types, Sizes, Angles and How to Choose

i Quick Answer

Framing nails are collated nails loaded into a nail gun and driven into structural timber — used for studs, plates, noggins, subfloor and decking frames. They’re specified by diameter, length, head type, shank pattern, collation angle and finish. Timber Central’s range runs 75mm at 34° collation (A Grade, Gasload, Paslode) in bright or galvanised finish, plus a 15° screw-shank coil nail option (2.5 x 32mm) for cladding and lighter fixing work. Coil nails and framing nails require different nailers and aren’t interchangeable.

✓ Key Takeaways

  • Framing nails are specified by diameter, length, head type, shank pattern, collation angle, collation material and finish — all seven affect nail gun compatibility and job suitability.
  • 75mm is the most commonly stocked length (3.1mm A Grade / 3.06mm Gasload & Paslode); the A Grade range runs from 50mm to 90mm.
  • D-head is the standard head format across Gasload and Paslode; clipped-head is a common industry alternative not currently stocked.
  • Shank types differ by product: smooth (Paslode), screw (coil nails), and ring (recognised market format, not currently stocked).
  • 34° collation applies to all strip framing nails; 15° applies to coil nails — angles must match the nailer and aren’t interchangeable.
  • Finish should follow the project spec: bright steel for general use, hot-dip or electro-galvanised where corrosion resistance is required.
  • H3 and H4 treated pine are stocked alongside the framing nail range for outdoor-exposure projects.
  • Framing nails and coil nails need different nailers, even where applications overlap, such as truss work.
  • Before ordering, confirm nailer compatibility, length/diameter, finish, shank type and pack quantity (3,000 for strip ranges, 6,000 for coil nails).

Stand on any timber frame site for ten minutes, and you will hear the same argument: bright or galvanised, 75mm or 90mm, paper collated or plastic. 

Framing nails look like a simple product until you are the one filling out an order and realising “nails” covers a dozen different specs.

This guide walks through how framing nails are sized, the head and shank types you will come across, and what collation angle actually means. 

Whether your paperwork says framing nails or nails for framing, the goal here is the same: understanding the spec sheet before the delivery truck shows up.

What are Framing Nails?

Framing nails are collated nails designed to be loaded into a nail gun and driven quickly into structural timber. They are used for studs, plates, noggins, subfloor sheets, decking frames and general timber-to-timber fixing on a build.  Because they are collated, meaning joined together in a strip or coil, they feed through a nailer without the operator having to load one nail at a time.  

The term covers a range of products. Diameter, length, head shape, shank pattern, collation angle, and finish all vary. Each spec affects which nail gun the product runs in and what job it suits. 

How are framing nails sized and specified?

Framing nails are specified by two numbers: diameter and length. It is written as something like 3.1 x 75mm. The diameter is the shank thickness, and the length is measured from the tip to the underside of the head. 

  • Diameter affects how much material the nail is driving through and how it sits in the timber. 
  • Length needs to suit the thickness of the timber being joined. Because a nail that is too short won’t achieve a solid fix, and one that is too long can punch through the other side.

On the Timber Central range, 75mm framing nails (3.1mm and 3.06mm diameter, depending on the product) are the most common length stocked, covering the A Grade, Gasload and Paslode ranges. The A Grade paper collated range is also available from 50mm to 90mm, so you can source longer or shorter runs in the same collated format. Coil nails sit in a different size bracket entirely at 2.5 x 32mm, which reflects their role in cladding and sheet fixing rather than structural framing.

Framing Nail Head Types

The head is what the nail gun’s driver strikes, and what ultimately holds the timber together.

Framing Nail Head Types

  • D-head (offset round head): the format used across Timber Central’s Gasload and Paslode ranges.
  • Fuller bearing surface: a D-head gives more contact area than a clipped-head nail, while still allowing nails to sit close together in the collated strip.
  • Clipped-head: a section of the head is removed so more nails fit per strip — a common industry format, though not part of Timber Central’s current head-type range.
  • Not interchangeable: the head type must match what the nail gun’s magazine and driver are built for, so it isn’t something to substitute casually.

Nail Shank Types: Smooth, Ring and Screw

Shank pattern is a separate spec from head type, and it affects how the nail grips the timber once driven:

  • Smooth shank is a plain, straight nail. It’s the shank type used on the Paslode framing nails in the Timber Central range, and it’s common across general timber framing work.
  • Screw shank has a spiral thread pattern. The Timber Central coil nail range uses a screw shank, which is built for better grip, particularly when fixing thin material like cladding sheets to timber framing.
  • Ring shank nails have circular ridges along the shank rather than a spiral thread. They’re a recognised format across the framing nail market, distinct from both the smooth and screw options above.

Collation Angles and Collation Materials

Collation angle describes the angle at which nails sit relative to each other inside the magazine strip or coil. It’s a defining spec because a nail gun’s magazine is built for one angle range, and nails collated outside that range simply won’t load or feed properly.

We stock strip framing nails (A Grade, Gasload, and Paslode), some are collated at 34°, a common angle for full-size framing nailers. The coil nail range runs on a 15° angle, which suits the coil-style magazine on compatible coil nailers.

Collation material also varies:

  • Paper tape holds the A Grade and Paslode strips together and burns away cleanly on firing.
  • Plastic collation is used on the coil nail range, reducing loose debris compared with older wire-collated formats.
  • Wire collation is another format used across the broader market, though it’s not part of Timber Central’s current range.

Bright vs Galvanised Framing Nails

Finish is one of the first things worth checking against a job spec, since it affects what the nail is suited to.

ProductSizeCollationFinishShank
Framing Nails A Grade3.1 x 75mm34° paperBright steelStandard
Framing Nails Paslode3.06 x 75mm34° paperHot-dip galvanisedSmooth
Framing Nails Gasload3.06 x 75mm34° Hardened bright steelStandard
Coil Nails A Grade2.5 x 32mm15° plasticElectro-gaslvanisedScrew

Say a carpenter is pricing up a job and has two boxes in front of them: 75mm bright framing nails and a 75mm galvanised option of a similar length. The bright steel nails are the cheaper, general-purpose option. The galvanised pack costs more per box but carries a corrosion-resistant coating. Which one fits the job depends on what the project spec calls for, since that’s a decision based on the architect’s or builder’s documentation rather than a general rule of thumb.

Nails for Treated Timber and Outdoor Applications

Timber Central stocks H3 and H4 treated pine alongside its framing nail range, covering projects where the timber itself is treated for outdoor exposure. When a project spec calls for a corrosion-resistant fastener to pair with treated timber, the current range includes Paslode hot-dip galvanised framing nails and electro-galvanised coil nails.

Nails for Treated Timber and Outdoor Applications

Fastener selection for treated or outdoor timber should always follow the project’s engineering or manufacturer documentation rather than a general assumption, since treatment class and exposure conditions vary from job to job.

Got a spec that calls for a specific finish or nailer match? Contact our team, and we’ll confirm what’s in stock against your requirements before you place the order.

Matching Framing Nails to Your Nail Gun

Framing nails for nail guns need to match the tool on three fronts: collation angle, nail length range, and head or shank format. A 34° collated strip won’t feed through a magazine built for a different angle, regardless of how close the numbers look on paper.

Timber Central’s stocks Gasload and Paslode framing nails which are built for gas-powered framing nailers, including Paslode Impulse, FrameMaster and FrameMaster-Li models. The A-grade paper-collated range suits compatible 34° framing nailers more broadly.  

Confirm compatibility between the specific framing nails gun model and specific nail products in the nailer’s manual or the manufacturer’s specifications, since gun models can vary even within the same collation angle.

Framing Nails vs. Coil Nails

Framing nails and coil nails both load into pneumatic or gas nail guns, but they are built for different jobs:

FeatureFraming NailsCoil Nails
Length75mm and up2.5 x 32mm 
Feed formatFlat stripCoiled roll
Best suited forStructural work — studs, plates, subfloor, general framing Cladding, fixing thin metal to timber, truss work
Nail profileStandard count, larger profileHigher nail count, smaller profile
Nailer requiredFraming nailerCoil nailer

Coil nailers and framing nailers are different tools. So the two formats aren’t interchangeable, even where the applications overlap, such as truss assembly.

What to Check Before Buying Framing Nails?

A few specs are worth confirming before placing an order, since getting one wrong is the most common reason boxes get sent back:

  • Nailer compatibility: collation angle, head type and magazine capacity all need to match the tool.
  • Length and diameter: check against the timber thickness specified for the job, not a general assumption.
  • Finish: bright, galvanised or electro-galvanised, matched to whether the fixing is indoor, outdoor or paired with treated timber.
  • Shank type: smooth, screw or ring, depending on what the job spec or engineering documentation requires.
  • Pack quantity: box sizes vary (3,000 for the strip ranges, 6,000 for coil nails), which matters when pricing a job at volume.

Mixing up collation angle or head type between similar-looking boxes causes the most on-site frustration, since the nails simply won’t load once the box is opened.

Final Summary

Framing nails may look simple, but the spec sheet behind them isn’t. Diameter, length, head type, shank, collation angle, and finish determine the right fix for the job. Timber Central’s range covers 75mm framing nails in bright and galvanised finishes, plus a 15° screw-shank coil nail option, all specified to Australian Standards. 

FAQs

Chat on WhatsApp (+61 404 067 699)